Assuming you have a gas furnace, the following steps will show you how to light a furnace. If you have an oil furnace, please consult a professional as oil furnaces require special care when lighting. 

1. Locate the gas valve handle on your furnace. This is usually located near the bottom of the furnace. 

2. Turn the gas valve handle to the "on" position. You will know the handle is in the correct position when it is parallel to the pipe leading to the furnace. 

3. Find the pilot light. This is usually a small red or blue flame located near the bottom of the furnace. 

4. Use a long match or lighter to ignite the pilot light. Hold the flame to the pilot light for at least 30 seconds to give the gas time to ignite. 

5. Once the pilot light is lit, turn on the furnace switch. This switch is usually located near the top of the furnace. 

Your furnace should now be lit and ready to use. If you have any trouble lighting the furnace, please consult a professional.

How To Light A Furnace

Check the safety devices on the furnace, such as the pressure switch, limit switch, and flame sensor

Lighting your furnace for the first time can be a daunting task, especially if you’ve never done it before. But with a few simple steps, you can get your furnace up and running in no time. Before you do anything, however, it’s important to check all of the safety devices on the furnace, such as the pressure switch, limit switch, and flame sensor. This will ensure that your furnace will operate safely and efficiently.

The pressure switch is a safety device that monitors the air pressure in the furnace’s combustion chamber. If the pressure becomes too low or high, the switch will shut off the furnace to prevent damage. To test the switch, turn the power off to the furnace and disconnect the wiring from the switch. Reconnect the wiring and turn the power back on. If the switch does not turn on, it needs to be replaced.

The limit switch is another important safety device. It monitors the temperature of the furnace and will shut off the power to the furnace if it gets too hot. To test the switch, turn the power off to the furnace and disconnect the wiring from the limit switch. Reconnect the wiring and turn the power back on. If the switch does not turn on, it needs to be replaced.

The flame sensor is a device that detects whether or not the furnace is lit. It will shut off the power to the furnace if it senses that the furnace is not lit. To test the sensor, turn the power off to the furnace and disconnect the wiring from the flame sensor. Reconnect the wiring and turn the power back on. If the sensor does not turn on, it needs to be replaced.

Once you have checked all of the safety devices on your furnace, you can move on to the next step of actually lighting the furnace. Make sure to follow all instructions provided by the manufacturer and be extremely careful when dealing with any kind of fuel. It’s also a good idea to have a fire extinguisher nearby in case of an emergency.

Now that all of the safety devices on your furnace are in working order and you’ve taken all necessary safety precautions, you can move on to lighting your furnace

Ensure that the furnace is off and all gas valves are closed

When it comes to lighting a furnace, safety is paramount. Before you attempt to light a furnace, you must ensure that the furnace is off and all gas valves are closed. This is a critical step that should not be overlooked, as it can prevent dangerous situations from occurring.

The first step to ensure a safe furnace lighting process is to turn off the furnace. You can do this by either flipping the switch located on the side of the furnace or by turning the thermostat to the “OFF” setting. Once the furnace is off, you should then close all gas valves. These valves are typically located on the side of the furnace and can be opened and closed by turning the knob. Make sure all gas valves are closed before you proceed.

Next, you should check that the pilot light is off. The pilot light is a small flame located near the gas valve and is used to ignite the furnace. To check the pilot light, simply look through the viewing window located near the gas valve. If the pilot light is on, you must turn it off by pushing and holding the red button near the gas valve.

Once the pilot light is off, you can begin the furnace lighting process. Start by turning the gas valve knob to the “ON” position. Then, press and hold the red button near the gas valve. After a few seconds, the pilot light should ignite. Keep the red button pressed until the pilot light is burning steadily. If the pilot light does not ignite after a few attempts, you should call a certified HVAC technician for assistance.

Once the pilot light is lit, you can finish the furnace lighting process by turning the thermostat to the desired temperature setting. This will turn on the furnace and the pilot light should stay lit. If the pilot light turns off, you will need to repeat the furnace lighting process.

By following these steps, you can ensure a safe and successful furnace lighting process. Remember to always turn off the furnace and close all gas valves before lighting the furnace, and if the pilot light does not ignite after a few attempts, contact a certified HVAC technician for assistance.

Turn the gas valve(s) and the pilot light (if applicable)

Lighting a furnace is a simple, yet important, step in home maintenance. Knowing how to turn the gas valves and the pilot light, if applicable, can save you time and money in the long run.

Before you begin, make sure to shut off the main power to the furnace. This precautionary measure will ensure your safety and prevent any potential damage to the system.

First, locate the gas valve. It is typically near the bottom of the furnace and will have a key or lever used to turn it on. Turn the key or lever counter-clockwise until it is fully open. This will allow the gas to flow into the furnace.

If your furnace has a pilot light, you will need to turn it on as well. This is usually located at the bottom of the furnace, near the gas valve. To start the pilot light, use a long-handled lighter to ignite the flame. Once it is lit, turn the knob of the pilot light to the “on” position. This will keep the flame burning and will provide heat to the furnace.

Now that the gas valves and the pilot light, if applicable, are turned on, you can turn on the main power to the furnace. The furnace will begin to heat up and provide heat to your home.

It’s important to remember that furnace maintenance should not be taken lightly. If you have any questions or concerns about turning the gas valves and the pilot light of your furnace, contact a professional technician. They will be able to provide you with the knowledge and advice necessary to ensure your furnace is running properly and safely.

Conclusion

⁠⁠⁠⁠⁠⁠⁠

In conclusion, this article provides helpful tips on how to light a furnace. By following the instructions provided, you will be able to get your furnace up and running in no time.

Davis Howard

Davis Howard is a leading expert in LED and lighting energy based in the USA. With a wealth of experience and a passion for energy-efficient solutions, Davis has established himself as a key voice in the industry. He has a deep understanding of the latest trends and technologies in LED lighting, and is known for providing practical and innovative solutions to businesses and individuals looking to reduce their energy consumption. In addition to his work in the field, Davis is also the author of the popular blog ScottRobertLadd.net, where he shares his insights and expertise on all things related to LED and lighting energy. With a commitment to promoting sustainable energy practices and helping others to make a positive impact, Davis Howard is a highly respected figure in the LED and lighting energy community.